SHIPPING QUOTE FOR OVERSIZED ITEMS MUST BE REQUESTED | WhatsApp Global CLICK HERE
$ 4,795.00 USD $ 5,110.00 USD
With the Soil oxygen content analysis system you carry out a soil gas analysis easily and quickly with the help of a needle probe and an oxygen content meter, without the need for drilling.
This robust system consists of a short soil probe and an oxygen content meter. The probe is pushed into the soil manually. Once at the right depth the probe is lifted slightly to open it. Subsequently the oxygen content meter is connected to the probe and with the aid of a bellows, soil gas is sucked through the meter and the O2 content is measured, which is an important growth parameter for trees and plants.
The probe has a small dead volume, so that a measurement can be taken accurately within a few minutes. The meter allows measurements up to 0% O2 content.
The oxygen content meter works with an electrochemical cell. This cell has a limited service life (about 1.5 years), but can be easily calibrated with air (21%) and with an oxygen-free gas (natural gas, nitrogen).
Note: Please note that the meter requires regular renewal of the O2 sensor.
Specifications |
|
---|---|
Cable Length | 1 m |
Range | 0 - 25% volume |
Calibration | Oxygen |
Detection Method | Electrochemical sensor |
Response Time | Within 6 seconds |
Sampling Method | Hand aspirated |
Batteries | 9 Volt transistor type |
Operating Hours | Approx. 30 |
Operating Temperature | -12 to +45 °C |
Weight | 11 lb |
EO20231603
$ 6,921.00 USD
The Beeker type sediment sampler is rod-operated and has a closable cutting head and piston. This sampler is used for high accuracy sampling of very soft to medium hard sediment layers. A standard and extended set are available.
With the Beeker sampler, you can take undisturbed sediment samples in a fast and certain way from watery sediment to unconsolidated sand to a depth of 5 metres. Even in watery conditions, the sample will not be lost thanks to the closable cutting head. Using additional extension rods, sampling to greater depths is possible in certain cases. The Beeker sediment core sampler works almost the same way as a Multisampler / piston sampler, but with a lockable head with inflated membrane.
The samples are taken in a transparent tube which allows you to make a clear profile description. The sampler has long sampling tubes of 1 metre. The piston can be operated directly with a rod, so that the sample can be pushed out of the sampler on site into a sample bucket. The apparatus is pushed or hammered into the sludge. To avoid compaction of the layers, a piston is held at a stationary position relative to the sludge. The sample can then be emptied into a clean stainless-steel bucket, or layer by layer in wide necked sample jar. It is not necessary to assemble and disassemble the apparatus with every new sample. This set comes in an aluminium transport case.
In addition to the standard set (04.23.SA), an extended set (04.23.SB) is also available for sampling and discharging core samples with a length of 1 metre or 1.5 metres, in bucket or jars and to transport and divide in subsamples with water pressure. This set is suitable for sampling of submerged soils to a depth of 5 metres from very aqueous sediments to unconsolidated sand.
Note: If you have any questions, please contact one of our experts.
Características |
|
---|---|
Connection | Screw thread |
Sampling Diameter | 57 mm |
Maximum Sample Depth | 5-8 m |
Product Material | Stainless steel, iron, PVC, other material |
Power Supply | Manual |
Sampler Position | Vertical |
Sample Length | 1 m |
Sample Stored in | Tube PVC transparant (ø 63 x 57 mm) |
Tube Length | 1 m, optional 1.5 m |
Sample Volume | 2.4 - 3.5 l |
Package Size | 146 x 62 x 54 cm |
Weight | 57 kg |
EO 20230727
Request Quote
Granular composition test set, complete with electromagnetic sieve shaker and standard set of sieves for dry and wet sieving. Suitable for the determination of the particle size distribution of soil samples.
Particle size distribution determination with our granular composition test set helps to classify the soils on the basis of international standards. The set contains:
The electromagnetic sieve shaker keeps the sample in continuous motion, for the best possible sieving results and accurate determination of the granular composition. The sieve shaker and the stainless steel mesh sieves (including receivers and lids) are suitable for both wet and dry sieving.
Note: The granular composition test set is used to analyse coarse fractions of soil samples. To perform a complete analysis or the grain-size of soil samples, the hydrometer set, for smaller fractions, is needed as well.
Características |
|
---|---|
Measuring Range | 0,063 micron - 8 mm |
Sample Specification | Disturbed |
Sieves Diameter | 200 mm |
Sieves Height | 50 mm |
Sieve Openings | 0,063 mm, 0,090 mm, 0,125 mm, 0,180 mm, 0,250 mm, 0,355 mm, 0,500 mm, 0,710 mm, 1,0 mm, 2,0 mm, 4,00 mm, 8 mm |
Power Supply | Line voltage |
Voltage | 240V 50Hz |
Weight | 130 lb |
EO20232103
Request Quote
The Royal Eijkelkamp penetrologger is a versatile instrument for in-situ measurement of soil penetration resistance. This electronic penetrometer comes with a built-in datalogger and memory for up to 1500 measurements.
This lightweight penetrologger of Royal Eijkelkamp is ergonomically designed and can measure up to a depth of 31.4 inch (80 cm). The penetrologger is used to measure the penetration resistance of the soil. The penetration resistance is a means to determine the carrying capacity of the soil and the ease with which roots can grow through the soil. This is important in agricultural, farming, and civil engineering techniques.
With the built-in data logger, the data is easily stored for further processing on your PC. The penetrologger contains an accurate internal GPS system (16 channels GPS receiver) to determine the exact measuring location. The coordinates stored in the penetrologger can be linked to a location or map using software (or less accurately via the Internet). The penetrologger results are displayed in MegaPascals (MPa) and Newtons (N) as a function of depth. The penetrologger also derives the Cone Index (CI).
Characteristics |
|
---|---|
Angle of cone | 60 ° |
Battery life | 8 hours |
Cone surface range | 1, 2, 3.3, 5 cm² |
Data output | .txt, other |
Data plug type | RS232 |
Data storage capacity | 1500 measurements |
Data transfer | Cable |
International Protection Rating | 54 |
Maximum Applicable pressure | 10000 kPa |
Maximum measuring depth | 31.4 inch |
Maximum operating temperature | 50 ° |
Measuring accuracy | ± 1% |
Measuring range | 0...10000 kPa |
Minimum operating temperature | 0 ° |
Product material | Stainless steel, iron, PVC, other material |
Programming possibility | Yes |
Reading accuracy | 0,1% |
Registration type | Logging |
Package size | 23.6 x 11.8 x 9.4 inch |
Weight | 34.1 lbs |
Request Quote
Characteristics Measuring range: 5-55% Accuracy: 5% Resolution: 1% Output signal: 0-1 Vdc Measuring pens material:...